Don’t have a dyno tuning centre nearby? Are you more of a D.I.Y. (do it yourself) type? Are you constantly changing parts on your bike? If you answer 'yes' to any or all of the questions above, then our Auto Tune kit is for you. The Dynojet Auto Tune kit is an 'add on' accessory that can be used with any of our Power Commander V’s.
Jul 23, 2012 Firstly did you turn the Auto tune option on in the configuration settings this can be found under power commander dropdown menu (from memory, sorry I am on my iPhone at work) The green light will only come while engine is running and you are above 2% throttle and after the 60 second delay then only while it is making adjustment also you should have an AFR reading on the display.
It connects to the PCV with a single cable and requires only a ground and +12 volt connection to be made to install (Harley models include connector for plugging directly into the bikes’ +12 volt line). If your exhaust does not already have one, a 'weld in' O2 sensor bung is included.
'Well, how does it work and what does it do for me?'
We have taken virtually the same technology that our patented Tuning Link dynamometer software (for automated Dyno tuning) uses, along with Bosch Wide Band O2 sensors and miniaturized it to be used on your bike, ATV, or UTV, while you ride. Once installed, the Auto Tune kit monitors the fuel mixture (by installing the included Wide Band O2 sensor in the exhaust). It then sends this information to the Power Commander V and automatically corrects it while you ride. Each map that we offer has pre-set Air/Fuel ratio values included that we find to be the best overall settings. This lets you simply plug in the unit and let it do the work. For Harley Davidson models we ever monitor and adjust each cylinder individually for increased precision as on these models required fuelling can vary significantly between the front and rear cylinder.
For advanced users that would like to change the Air/Fuel ratios from our baseline they are fully adjustable. Each throttle opening/rpm combination is individually adjustable, so that you can have both fuel economy, during cruise, while maintaining peak output at larger throttle openings. For most
models of bikes, it is also possible to adjust the Air/Fuel ratios 'per gear'. This gives you total control of the fuelling in every gear and throttle/rpm area if required.
The Auto Tune kit can be configured to run and correct at all times or by using the 'map switch port' on the PCV. You can set it up so that you can switch back and forth between the tuning modes and the base map settings. You can also configure the Auto Tune kit to wait until the bike is at a certain operating temperature before beginning to make adjustments.
Auto Tune kits
Part #: AT-100, AT-100B, AT-101 and AT-101B
These are a 'dual O2 sensor' versions made specifically for Harley Davidson models. They come with two O2 sensors, a control module with 2 sensor inputs, a CAN connection cable, CAN termination plug, and two custom length sensor cables. They also includes a built in power connector that plugs directly into the bike's stock wiring harness for easy connection. AT-100B and AT-101B also come with 2 weld boss kits supplied.
Part #: AT-200
This version is a 'universal fit', single O2 sensor kit. It can be used on any vehicle that has a PCV installed on it. It comes with a single O2 sensor, 'cut to length' sensor cable, control module, O2 sensor, one weld boss kit, a CAN connection cable, and CAN termination plug. It requires a ground and +12 volt connection to be made using the supplied wiring hardware. .
Part #: AT-300
This Auto-tune Universal kit is designed for twin cylinder motorcycles/ATVs that use the Power Commander V allowing control of two cylinders separately and simultaneously. The kit includes two O2 sensors, a control module with 2 sensor inputs, a CAN connection cable, CAN termination plug, two custom length sensor cables, and two weld boss kits. It also requires a ground and +12 volt connection to be made using the supplied wiring hardware.
Install Guides
Power Commander Auto Tune Won't Run Game
Please Note
AutoTune devices will NOT drive a gauge. The WideBand2 will drive a gauge and pass the necessary information to a Power Commander V for the AutoTune function to work. To use these kits your exhaust must have an 18mm bung installed. If your current exhaust does not have this size bung you must weld one on. Certain kits come with the necessary weld-on bung.
Power Commander Auto Tune Reviews
The latest Dynojet Power Core C3 Tuning Software offers advanced Auto-tune setup capabilities in which you can designate specific O2 sensor channel streams to specific cylinders.
To view our products, please select your bike above.